APPLEBOX - the Apple-1 pages		  
 

 
    
   the Apple-1 expansioncards

  
 
possible Orders up till now: 
    6		    B ) Apple1 Prototypecard  ( After revision and correction! )
  		 
    In the second step after i started with the design of the slotexpansionboard - and after i discovered that at the slotedgeconnector the + 12 Volt and - 12 Volt only
  were present as non stabilized power i revised the availiable amount of power at this point. By definition of the transformator delivered with the original Apple-1
  there would only be 1 Ampere availiable. In fact i also had prepared the slotexpansionboard to ba able to get the 12Volt positiv and negativ also by choice
  from an external powersupply but there still was the question open about the use of the expansioncards in different slots. If the card would be inserted in the
  "on board" slot, that slot would still offer only unstabilized power, because the stabilization would only regulate the power at the slots of the slotexpansion
  itself. So i decided to also offer the opportunity of populating a stabilization on the card itself - if it was desired to use it within the "on board" slot.
  In fact at the slot only the +5 Volt is oīffered as stabilized voltage and the -5 Volt is not availiable at all. So i added the opportunity to get that voltage
  "droping out" from the -12 Voltage branch. In case the card should be used in the slots of the slotexpansioncard there would still be the possibility to
  hardwire bridges to the +12 Volt regulation and the -12 Volt regulation - but still populating the - 5 Volt, if that powersource would be needed as stabilized voltage.

  In the first version for testing purposes i only made a simple trace for proof of the functions, but for the cards that will later be offered for ordering, od course
  there will be extended thick traces to offer a lot of short wiring from "power-source-rails" of + 5 Volt, - 5 Volt, + 12 Volt and - 12 Volt  to the electronics soldered
  in the card. And if the options of stabilizing the voltages on the card are used - there is enough space left remaining - to use coolingsinks for the voltageregulators.

  Some of the possible uses of the prototypecard might be projects like a PIA-card fot control of a printer with parallelport to printout listings, or a prototypecard
  with a SIO chip to control either modem or serial printer or the version with the PIA to control external devices with optocopling ICīs or relais. The card permits
  the freedom to keep off all that kind of experiments or interfaces from the mainboard and the different projects are only limited by the phantasy of the user.

  If using wirewrap connectionlins at the 2 rows above of the socketconnectionpads itīs also possible to examine the signals at the slot with "homebrew"
  connectioncables at an oscilloscope.
 
    
Frontside / populationside  Backside / soldering side

 ACI  Size compare to expansioncards

  
 
 
 
 
  ◄ turn back to the indexpage ←
 due to european laws and german court decision:
 I hereby declare no responsibility to any "deep links" resulting from the links in this page. I have no influence to the pages linked hereby in this page and the
 contents in those pages. I therefor canīt take any kind of responsibility to contents in the pages, where these links direct the readers browser to nor to the
 contents resulting from following up links from those pages. The reference to contents by this links is dependent ro the status of the date when the links have
 been set ( April 2013 ) and it might occur that references and contents may change by the fact that domains may have been discontinued from their former owners.
 In such cases i canīt take any kind of responsibility to the changed contents. this is specialy valid to banners, advertisements or merchandising links in the targeted
 pages.

Đ copyright: Harro Walsh 2013